A Step-by-Step Overview to Installing a Bath Tub
A Step-by-Step Overview to Installing a Bath Tub
Blog Article
Were you looking for resources concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bath tub isn't exactly brain surgery, yet it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough project. If the old tub is conveniently accessible, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and also place the new bathtub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will need a helper to leave the old tub and set in the new one. Make certain you have actually certified on your own for the work and are comfortable attempting it. Instead of employing a professional to take over a halfway-completed task, it is far better to consider employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This short article will certainly aid you mount a new bathtub in your restroom if you have actually currently gotten a brand-new bathtub and don't need to change the plan of your previous water system pipelines.
Your devices and also product list should comprise the following:
Getting ready for the Setup
To start with, the supporting framework supplied with the bath must be fitted (if needed) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps unit to prevent stress on the tub.
Fit the flexible tap ports to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, after that the first thing you should do is separate the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of removing the existing faucets can be quite bothersome because of the restricted gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel all set for the remaining water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Using the two wood boards under its feet, position the bathtub in the required setting. The wood boards are handy in uniformly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bath tub till the level reads level.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other faucet.
Turn on the water system and also examine all joints and also new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Protect the tap in position with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap finishes first, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in issues with dampness and also possible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to allow for the motion experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily readily available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our article about How to Install a Bathtub Yourself. Thanks a lot for finding the time to read our content. Are you aware of another person who is fascinated with the niche? Be sure share it. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Recurring Service Plans
Report this page